Not sure which wick your kerosene heater takes? Work down this page. Most people find their wick in step 1 or 2. If you don't, measure the old wick, send us the numbers at the bottom of the page, and we will match it for you.
1 Look for the brand and model
Check the heater for a label or stamped plate. It is usually on the back or bottom of the cabinet, on the base tray, under the fuel tank lid, or on the front of the owner's manual. Write down the brand name and the full model number.
2 No label? Check the old wick or manual for a number
Some wicks have a number printed on the cloth band, and many manuals and parts lists give a wick part number. If you have any wick number at all, look it up here.
3 Still stuck? Measure the old wick
"Odd" heaters were made by a reputable factory and sold to a chain store under a different name and model number, or sold in another country under another name. So the wick exists. It is just a matter of matching it to your heater. We have over 100 different wicks in stock and the measurements of every one of them on file.
There are four measurements we need. It is much easier to remove and measure a dry wick, so empty the fuel tank and burn the wick dry first if you can.

A. Wick diameter
Measure across the central air pillar the wick fits around, then measure outside to outside across the wick gap. The wick diameter is the average of the two. Example: the pillar is 2 1/2" and the outside of the gap is 2 5/8", so the wick is 2 9/16" in diameter. There are 12 different wick diameters, so this one matters.

B. Flat width C. Length
Take the wick out, press it flat, and measure across the cloth band (width) and top to bottom (length). A worn wick has burned down, so it was probably 1/8" to 1/4" longer when new. The wick in the photo is 5 1/4" wide and 5 3/4" long. Note any metal wick-raising attachment like the one shown. It helps identify the wick.

D. Top of the wick to the pins (if it has pins)
Some wicks are the same diameter and length but have the pins either 2" or 2 1/2" below the top. Add about 1/8" to your measurement to allow for wear. With the pins too high the wick cannot be raised enough to burn properly. With the pins too low the wick sits too high and will not retract enough to turn the heater off.
No pins on your wick? Then the wick sleeve has sharp barbs inside to grip the wick. Just tell us "no pins."
Standard kerosene heater wick sizes
Modern kerosene heaters were invented in Japan, and most wicks match one of these sizes. Width is the flat width across the cloth band.
| Flat width | Wick diameter |
|---|---|
| 3 1/8" (80mm) | 2" (50mm) |
| 4 1/8" (105mm) | 2 9/16" (64mm) |
| 4 3/4" (120mm) | 2 15/16" (75mm) |
| 5 1/2" (140mm) | 3 3/8" (85mm) |
| 6 1/8" (155mm) | 3 3/4" (95mm) |
| 6 1/2" (165mm) | 4 1/8" (105mm) |
| 7 1/2" (190mm) | 4 3/4" (120mm) |
★ Older heaters (Perfection, Florence, Wards and similar)
On these, the diameter of the draft tube decides the wick. Take the burner off so the draft tube is the only thing standing up from the tank, and measure across it. A Perfection draft tube is 2.50", so if yours is larger, a Perfection wick or wick #3L will not fit.

If any of the old wick is left, take it out of the wick sleeve, press it flat and measure across. A Perfection clone that uses wick #3L will be 4 3/8" wide. Also tell us whether the wick fits inside or outside the wick sleeve, and the diameter of the sleeve.

Photos help us recognize a heater, but they cannot be measured accurately, so please send the numbers too.
4 Send us your measurements
Fill in what you can below. We will compare it with our wick list and email you back with the wick that fits. If you have photos of the heater, the label or the old wick, you can reply to our email with them.