Photo Album
Heater and Lamp Flame Spreaders
Flame Spreaders from Heaters in the Past 100 Years
The following is a small sample of lamp flame spreaders. This page is a work in progress as I find the time to finish it.

|
| Left to right: Admiral, Rayo #22, B&H 1904, Naugatuck, Miller, Improved Bristol, B&H 6.2.96, B&H 7.1.90. |
`

|
Size comparison, left to right, E&G #0, Standard, Miller #1, Radiant #4, Radiant #5.
|
`

|
Flame spreaders from the smallest to the largest, from left to right: Kosmos #15; P&A Royal; B&H; Beatrice 4012; Valor 420 Parlor Stove; and a Perfection 730.
|
More detailed lamp flame spreader photos. Click on the photo to enlarge.

|  |  |  |
Admiral, H B & H
| Admiral, H B & H | B&H "Tiny" | B&H "Tiny" |
 |  |  |  |
| Rex, "Tiny" B&H | Rex, "Tiny" B&H | B&H Radiant 5 | B&H Radiant 5 |

|  |  |  |
B&H #2, 1890 "Jauch"
| B&H #2, 1890 | B&H #89 | B&H #89 |

|  | |  |
B&H Radiant 4
| B&H Radiant 4 | | Ditmar Soleil |

|  |  |  |
| Improved Bristol | Improved Bristol | Improved Bristol | Improved Bristol |
 |  |  |  |
The most beautiful
| Bristol Brass | E&G 15''' | E&G 15''' |
 |  |  |  |
| Miller #2 | Vestal #1 | Miller Vestal #1 | Miller Dresden |
 |  |  |  |
| Craighead & Kintz | Craighead & Kintz | New Columbia (Matthews & Willard) | New Columbia |
 |  |  |  |
| P&A Naugatuck | P&A Naugatuck | P&A Royal #2 | P&A Royal #2 |
 |  |  |  |
| P&A Royal #1 | P&A Royal #1 | Banner Electric | Banner Electric |
 |  |  | |
| As-new P&A Royal #1 | P&A No. 1 Side | P&A No. 1 inside | |
 |  |  |  |
| P&A Plumwood after 1905 | P&A Plumwood | "Columbia" FS, made by P&A for M&W... | ...and sold by Trenton Lamp Co. |
 |  |  |  |
| Banner #3 | Banner #3 | Pittsburgh Mammoth | Pittsburgh Mammoth |
 |  |  |  |
| Rayo Long | Rayo Long | Rayo Short | Rayo Short |
 |  |  |  |
| Rayo, 1st year | Rayo 1905 | Rayo Socony | Rayo 22 |
 |  | | |
| Perfection - pre-Rayo | Perfection - pre-Rayo | | |
 |  |  |  |
| Rochester #2 | Rochester #2 | Rochester 1887 | Rochester 1887 |
 |  |  |  |
| Standard | Standard | Success | Success |
 |  |  |  |
| Unidentified | Veritas 30''' | Unidentified | W&W Agni |
 |  |  |  |
| 15''' Gaudard Matador | 15''' Gaudard Matador | 16''' CarolyBrenner | 16''' CarolyBrenner |
| | | |
| | | |
 |  |  |  |
| Hinks 20''' | Young's Court 20''' | L&B 20'' | L&B 30'' |
 | Making a post-type flame spreader requires several different machine tools, including a metal shaper and a lathe. This series of photos was taken as the work progressed by Peter Brickell. At left, an 18''' Vulcan reproduction flame spreader which was used as a sample for dimensions. At right is a brand new Vulcan flame spreader, but the story is in getting to that point! Note that the flame spreader is at the correct height for the Vulcan chimney. |  |
 |  |  |  |
| The post is turned on a lathe. | A metal shaper was used for the top of the post. | The disk is attached to the top of the post. | The new flame spreader fits the tube perfectly. |
| | | |