LAMP Wicks - LANTERN wicks

Center draft wicks and Aladdin lamp wicks on right column >>>
BY THE ROLL: LAMP wicks and LANTERN wicks
WICKS FOR (click on the name) KOSMOS LAMP WICKS,
ADLAKE, DIETZ AND OTHER LAMPS, BRITISH DUPLEX,
Student Lamp Duplex -Brooder Heaters,
P&A Harvard lamps, H.G. Moehring lamps,
Auto Motor Primer Wicks
Angle lamps
Round Woven Fiberglass Wicks (and cotton)
Wide Wicks for SAD IRON, Beatrice, GSW and Haller stoves.
Round wicks.
ZIPPO Lighter Wicks & Hand Warmer Replacement Burners
Lamp Chimneys
Keep vent holes open. Burner repair.
STANDARD LAMP WICKS by the package - see below
1/4'', 3/8'', 1/2'', 5/8'', 3/4'', 7/8'', 1'', 1 1/4'', 1_1/2''
Lamp Wick by the roll - 5 meter rolls (16.40 feet)
WHY BUY LAMP WICK BY THE ROLL?
MEASURE THE WIDTH OF THE WICK SLOT
to determine what width wick you need
FLAT WICK LAMP COLLAR DIMENSIONS
Individually packaged 5 meter (16.4 foot) rolls of nicely woven wicking. You cut the length you want from the roll. Lamps require thicker wicks than do lanterns, generally, so lantern wicking is listed separately below. Rolls require less handling and save a considerably amount of money per foot of wick. | |
| Each roll is inspected and individually packaged. I have these rolls of lamp wick made specially to my specifications of width and thickness so they will work perfectly in American lamps, or in the case of the 10 meter roll shown at right, in British Duplex lamps. I use Ames or Teclock fabric thickness gauges to ensure absolute conformity to my specifications. | 10 meter roll of Brit Duplex wick being measured for thickness. |
Lamp wicks are thicker than lantern wicks because of the greater fuel lift requirements of lamps as lamps have deeper fonts, lamps being designed for burning relatively long periods of time while providing a considerable amount of light while burning indoors. Lanterns were designed for burning outdoors and have a handle for carrying with some sort of wire protection for the chimney when being carried to a barn or outbuilding before flashlights were invented. | ||
Classic-style cotton lamp wicking is designed to be used with clear kerosene lamp fuel or high-quality modern lamp oil: Not for use with fuels containing mineral spirits, paint thinner, or turpentine, or any fuel with a flash point under 124 degrees F. The use of Liquid Paraffin Lamp Oil in Dietz lanterns voids the factory warranty. | ||
|
LAMP_WICKS by the ROLL (click photo above to see a roll)
per 5 meter roll
| Lanterns often require a thinner, very tightly woven wick to avoid tangling the wick in the star wheel wick raiser. 5 meters = 16.4 feet of wick. | ||
| 3/4'' - 19mm, 0.065'' thickness, black stripe, 0.060" thick (For some lanterns, not many Dietz though) - Please measure the width of the wick slot to get the correct wick for your lamp. 5m ROLL | per 5 meter roll | Order on WickShop.com |
MEASURE THE WIDTH OF THE WICK SLOT
to determine what width wick you need
FLAT LAMP WICKS by the package of three, 8'' long wicks or 24'' of wick. | Shop at WickShop.com | ||
| WICKS FOR DIETZ LANTERNS, Package of three, 7 1/2'' long wicks | |||
1/4'' | Various small night lights | Order on WickShop.com | |
3/8" | Dietz #50 Comet, Vesta RR lanterns; Acorn and Nutmeg burners (pack of 3) | Order on WickShop.com | |
| 1/2" | Dietz No. 76 Original; No. 0 Eagle and Banner burners Special; many French pump lamps (pack of 3) | Order on WickShop.com | |
| 5/8" | Dietz #20, #1 Little Wizard; #20 Junior, #40 Victor; Adlake Railroad lanterns; No. 1 Eagle, #10 Monarch; Banner Railroad and Queen burners, ; Badger "Solar" bicycle/carriage lamp (Made in Kenosha, Wis); #1 Rowatt burner. (pack of 3) | Order on WickShop.com | |
| 3/4" | Various #2 lanterns. Please measure the width of the wick slot to get the correct wick for your lamp. 0.070'' thick. (pack of 3) | Order on WickShop.com | |
| 7/8" | No. 70 Crescent, #8 Air Pilot, Miller Zenith burner, No. 70 Crescent, #80 Blizzard, #90 D-Lite, No. 70 Crescent, #90 D-Lite; #2 Rowatt burner (two wicks side-by-side) and Dietz #8 Air Pilot, #80 Blizzard, #90 D-Lite, and #2500 Jupiter oil lanterns. | Order on WickShop.com | |
| 1'' | No. 2 Eagle, Banner and Queen burners; for old time lamps and greenhouse heaters; early 1900's Dietz Blizzard, Royal HB; pack of three 8'' long wicks. | Order on WickShop.com | |
| A brief history of Feuerhand lanterns (pdf) | |||
DUPLEX LAMP and WIDE WICKS. When ordering 2 or more feet (strips) of wick, the length of wick you receive will be comprised of one uncut piece totaling the number of feet ordered - ie an order of 4 feet gets you a 4-foot length of wick that you can than cut as needed. | |||
| 1/2'' | 1/2'' X 24'', 0.068" for lamps/lanterns needing a thinner more tightly woven wick. Feuerhand #276 Baby. Price for two feet of wick. #911S | Order on WickShop.com | |
| 5/8" | 5/8'' x 24'', 0.068'' for lamps/lanterns needing a thinner more tightly woven wick. Price for two feet of wick. #912S | Order on WickShop.com | |
| 3/4'' | 3/4''' x 24'', 0.068'' for lamps/lanterns needing a thinner more tightly woven wick. Price for two feet of wick. #918S | Order on WickShop.com | |
| 7/8" | 7/8" x 24", 0.085" thick. Per two feet. Fits lamps & lanterns listed above. | Order on WickShop.com | |
| 1.0'' | 1.0'' x 24'', 0.080'' thick, for some American Duplex lamps. Price per two feet. #134 | Order on WickShop.com | |
| 1 1/16'' | 1 1/16'' x 24'' (or number of feet ordered), for pre-War Brit Duplex lamps. 0.070'' thick. Price per two feet. #121. How to measure width needed, click here | Order on WickShop.com | |
| 1 1/16'' | 1 1/16" x 10" pre-cut length for post-War British Duplex, P&A Duplex lamps and Brit greenhouse heaters. Pack of 2 wicks. Hattersley Green Stripe wicks are 0.104" thickness. Not for pre-WW1 Hinks, Veritas, Messenger's, Young's and other pre-War lamps. Victorian Era duplex lamps require wick thickness not to exceed 0.0990". #120 |
2 wicks | Order on WickShop.com |
| 1 1/8'' | 1 1/8" x 12'', 0.075'' thick, for American duplex burners requiring a wide, 1 1/8'' wick. NOT FOR B&H Student lamp. Go here for B&H Student lamp wicks. #119 | ||
WIDER FLAT WICK ARE BELOW
KOSMOS LAMP WICKS - CLICK HERE | ||
| 1 1/4'' x 24'' - (32mm) Kosmos weave, 2 feet of wicking | Order on WickShop.com | |
| 1 5/16'' x 24 (33.3mm) Kosmos weave. 2 feet of wicking | Order on WickShop.com | |
| 1 7/16'' x 24''- (38mm) Kosmos weave, 2 feet of wicking | Order on WickShop.com | |
| 1 1/2" x 24", THICKERBest wick for ANGLE LAMPS (0.087'') wick than individual 8" long pieces above. You cut to length desired. | Order on WickShop.com | |
| 1 1/2" x 24", thinner (0.078'') wick than individual 8" long pieces below at 0.066" thickness. Best wick for Miller brooder heaters (Original wicks in Miller #3 burners were felt!). You cut to length desired. | Order on WickShop.com | |
Because most Kosmos burners use gear wheels to move the wick vertically, Kosmos wicks must be of a harder, denser weave than common flat wicks made for cheap hardware store lamps - and that means they are more expensive to make. Wicks for Kosmos Lamps (1 3/8'' wide to 4" wide), CLICK HERE. | ||
| Wide, FLAT wicks P&A Harvard lamps, H.G. MOEHRING, some heaters and Sad Iron stoves are below | ||
| 2 9/16" x 8" (66mm) KOSMOS #14 & #15 BURNERS - "14 line"' Thicker wick 0.110" - Special Purple Stripe. For Kosmos lamps with a larger wick gap. Per wick. #125 | Order on WickShop.com | |
| 2 3/4" x 9" (72mm), Haller Stoves, P&A Harvard lamps, some flat wick H. G. MOEHRING lamps, some Sherwood lamps, 9" long. Medium thickness of 0.086". Per wick. | Order on WickShop.com | |
| 3" x 8", 0.070" thickness, for Fellboelin Mantle lamps. Special order | ` | |
| 3 5/8" x 8" (92mm), 20_line ''' flat wick, thicker wick - 0.086" for Imperial Kosmos Vulcan burners; Brenner Ideal #20i Burner/ Trawler Lamp; German 20''' Baldur Brenner; 20''' Schwintzer & Grff. (See photos of a large Kosmos-Brenner; photo 1, photo 2.) Perfect for sad iron heaters requiring 3 9/16 to 3 5/8" wide wicks. Installation instructions > click here SAD IRON STOVE WICKS Per wick. #126 | Order on WickShop.com | |
| 3 5/8" x 24" (92mm), 30''' flat wick, 24" of wicking (cut your own length) Thickness 0.076" - THIN WICK FOR SOME LAMPS & STOVES. ( 3 wick measure - 24" of wicking) #123 | Order on WickShop.com | |
| 3 5/8" x 24" (92mm), 30''' flat wick, 24" of wicking (cut your own length) Thickness 0.085" - THICKER WICK FOR SOME LAMPS & STOVES. ( 3 wick measure - 24" of wicking) #132 | Order on WickShop.com | |
| 4'' x 8" (101.6mm), 40''' flat wick Beatrice Boiling Stove, some Kosmos-Brenner burners. Fits many sad irons requiring 4" wide, thick wicks and & Canadian SMP or GSW "Hot Blast" heater, not for Daisy #9. Thicker 0.082" thickness. For info on Beatrice Boiling Stove, click here. #127 | Order on WickShop.com | |
| 4 1/2'' wide (114mm), 24'' long, flat wick, 0.086" thick. Fits Flamme Bleue No. 2 heater; Carl Holy Brilliant buner. For those rare burners using an extra wide wick, or for you to experiment by trimming to the width you want; Note that the cut edge must be Zig-Zag stitched if you cut it down so it will not unravel. #133 | Order on WickShop.com | |
ROUND Woven Cotton Wicks | ||
| 1/16" round woven COTTON wicks for, among other things, small Cognac Snifter warmers | Order on WickShop.com | |
| 1/8" round woven COTTON wicks for, among other things, LARGE Cognac Snifter warmers | Order on WickShop.com | |
Round Woven Fiberglass Wicks | ||
1/8'' (2.5mm) diameter Round Woven Fiberglass, | Order on WickShop.com | |
| 3/16'' (4.0mm) diameter Solid Round Woven Fiberglass. Fits: Dietz and Embury #40 Traffic Gard, Embury Luck-E-Lite, and Handlan #57. Also fits Adlake, Dressel, Armspear, and various other railroad marker and switch lamps. price on WickShop cents per foot | Order on WickShop.com | |
| 7/32'' (5.5mm) diameter Round Woven Fiberglass, price on WickShop per foot. | Order on WickShop.com | |
| 5/16" (8mm) diameter Round Woven Fiberglass, | Order on WickShop.com | |
| 3/8'' (10.0mm) diameter Round Woven Fiberglass, price on WickShop per foot | Order on WickShop.com | |
| Vapo Cresolene Vaporizer Lamps use Zippo lighter replacement wicks. | ||
Auto Motor Primer Wicks | ||
| Auto Motor Primer Wick, asbestos. I take no responsibility for the use of asbestos. See instructions here. | Order on WickShop.com | |
| Auto Motor Heater Wick, cotton. 3/4" x 8". NOW IN STOCK | Order on WickShop.com | |
3/4'' Diameter Smudge Pot, Tiki Torch wicks are the same | ||
Lamp Wicks by Manufacturer
Alphabetical List; Package of 3 wicks
MEASURE THE WIDTH OF THE WICK SLOT
to determine what width wick you need
ZIPPO Lighter Wicks & Hand Warmer Replacement Burners
| Zippo Lighter Wicks, Individual Card, one each per card | Order on WickShop.com | |
| Zippo Outdoor Line Hand Warmer Replacement Burner (Silver) | Order on WickShop.com |
MEASURE THE WIDTH OF THE WICK SLOT TO KNOW THE SIZE WICK YOU NEED.
When ordering lamp wicks, please measure the width of the wick slot on the bottom of the burner as shown at right in order to get the proper wick for your lamp. It is your responsibility to order the right size wick - I cannot do it for you. DO NOT ASSUME that all #2 size burners used the same size wick, for example. Various manufacturers over the past 150 years have labeled their burners according to their whim - there were no industry-wide standard dimensions. Measure, please. It is easy. |
Duplex wick lamps often use a "helper wick" between the two wicks used for burning. The "helper wick" is inserted through a loop between the two main wicks and each "tail" falls into the fuel. The fuel in the "helper wick" is passed to the main wicks where they touch just below the burner so more fuel is available to the top of the wick, hence the lamps burn brighter. The helper wick should be a minimum of 18'' long and many people use a 2 foot length of helper wick. So, with a 2 foot long helper wick and two 1 foot long main wicks, a total of 4 feet of wick is needed to properly wick a Duplex burner lamp. |
KEEP LAMP BURNER VENT HOLES CLEAN AND CLEAR
There is a small air vent in virtually all lamp burners, which is a safety feature to keep air pressure equal in the tank even with a solid fill plug. The vent hole must be keep clean and clear of obstruction. The photograph at left shows the bottom of a duplex burner, but single wick burners also have a vent. Click on the photo to enlarge it. When ordering flat lamp wicks, please measure the width of the wick slot as shown at left in order to get the proper wick for your lamp. The wick should not be jammed into the rounded corners of the wick slot as that would make movement of the wick more difficult and thus harder on the gearing. It is your responsibility to order the right size wick. |
Burner Repair. See the three star wheels attached to the shaft in each wick slot above? Those cog toothed star wheels must turn in fairly precise slots, and if one tooth is bent the wick will only turn back and forth until the bent tooth hits the side of the slot. Look closely and you should be able to identify the bent tooth. Gently push the errant tooth back into alignment with a thin bladed screwdriver, then try the wick raising knob again. It may take a few tries, but it is often possible to make a seemly broken flat wick burner work again just like new. This is also the time to gently push any dents in the fairing above the wick back into place, which will result in a smooth air flow over the wick and thus a nice, even flame. Be gentle. All of these parts are usually brass. |
FLAT WICK LAMP COLLAR DIMENSIONS
KOSMOS BURNERS #6 Kosmos 15/16" I.D. collars #8 Kosmos Burner 1 1/16" I.D. collars #10 Kosmos Burner 1 1/4" I.D. collars #14 Kosmos Burner 1 1/2" I.D. collars FLAT WICK BURNERS #Number 1 Size - has an opening of 7/8 of an inch in diameter. #Number 2 Size - has an opening of 1-3/16 inches in diameter. #Number 3 Size - has an opening of 1-13/16 inches in diameter. |
The comments below are from the late, great Dickson Stauffer, who had encyclopedic knowledge of lamps, is honest and a gentleman - my highest praise.
"After some research, I find that all kerosene burners had some sort of vent system. The most common today on flat wick burners is the little tube that runs along the main wick tube. This allowed the vapor that builds up in the font as the lamp heats up to vent directly to the wick where is is burned. Others just have a hole that vents into the screened area of the burner. Central draft lamps evidently were vented by the spaces around the wick riser though Royals do have a small hole under the tab in the base for a direct vent. All these vent holes HAVE to be kept clean. I make a point now to go over the burners I use VERY carefully with the vent and air flow systems particularly in mind. I think it was fairly common for these holes to get plugged up by the gummy residue from the cheap kerosene." Dick Stauffer
Click here for"Wickless" Kindler Stove wicks.
(See chart for width and length needed)
At left is a scan of an old Victory Asbestos Wick box. The wick in the box was made to fit the old Boss and Perfection gravity flow, wick edge-burning stove designs known as "wickless" stoves, and wicks for them are available on the "wickless stove" page. The new Butterfly edge-burning stoves are copies of the 70+ year old Boss design. Good illustration of an eagle with the burning edge wick in it's mouth. |
CANDLE WICKING
I do not sell taper candle wicking or wicks for small string or rope wick lamps...it is almost too easy to make your own and save a fortune in wick costs. Candle wicks can be made from any pure cotton string or twine - available in almost every hardware store. Thick string will provide more light, and is more suitable for larger diameter candles. Use a thin string for taper or votive candles. For small "night light" kerosene lamps, 9/64" cotton twine is very inexpensive and will fit most small kerosene night lights.
One of the greatest discoveries of the early 1800's was that cotton wicking treated with boric acid did not "sputter" when burned. It is easy to make boric acid and "treat" your own cotton wicking material. I "treat" whole skeins of cotton string at a time and use it in candles I make with my solar melter. Wear gloves.
Take a roll or ball of cotton string and find a container into which it will fit completely, but not with a lot of excess room. Then make a solution of one (1) tablespoon of salt and two (2) tablespoons of Borax per cup of boiling water -- that IS the boric acid solution. Weigh down the ball of string in the container so it won't float up (find a rock) and pour in the boric acid solution, making sure you have enough to completely cover the cotton string. Let is soak for several days, then let it dry in the sun for several more days. If there are excess salt crystals covering the string, just wash them off with water and dry the ball of string again. Now you have the wicking necessary for making a lot of candles, cheap and easy!
*Please note that boric acid made with salt as above is not the same as stronger boric acid purchased in liquid form. Boric acid has many uses and can be toxic at higher concentrations. Look it up and read the precautions.
http://www.ehow.com/about_5419217_borax-vs-boric-acid.html






